Home > Grid Tie
Choose a sub category:
Enphase Energy MidNite Solar Solar Cables
Fuse Holders Combiner Box Conext
Sort By:
Page of 3
The Schneider Electric Automatic Generator Start (AGS) automatically activates a generator to provide a Conext™ XW or Conext SW inverter/charger with the power needed to recharge a depleted battery bank or provide additional power for heavy loads. The AGS’s generator management intelligence continuously monitors battery voltage, state of charge, and inverter charge modes. It uses this data to start and stop the generator when the battery needs charging. The AGS also starts the generator to assist the system’s inverter/charger(s) when output power demands are high.
The AGS is customizable. The user defines whether the generator should be activated by low-battery voltage, state of charge, thermostat operation, or load on the inverter(s). A quiet-time setting prevents the generator from starting at
inconvenient times. LED lights display the status, while all user-defined settings are programmed through the Conext XW System Control Panel (Conext XW SCP).

Features:
Compatible
    Connects to other Xanbus™-enabled devices without requiring additional hubs or control cards
  • Compatible with AC or DC generators with either two- or three-wire start controls
  • 20-contact generator connector and three built-in relays support 13 preset generator configurations
  • Interfaces with Conext XW and Conext SW inverter/chargers, Solar Charge Controllers, and Conext XW System Control Panel
  • Note: AGS requires a Conext XW SCP for configuration and monitoring

Flexible

    Comprehensive, customizable triggers (based on low-battery voltage, change in charging state, high inverter load, thermostat signals, planned exercise periods, maximum runtime, and quiet-time settings)
  • Non-volatile memory preserves settings through power interruptions
  • Built-in emergency shutdown
  • LED display showing at-a-glance status

The Gateway bridges the gap between a Conext or XW System and the system owner's computer, making it the central component for a residential or small commercial remote monitoring system.

The Gateway logs performance data directly from the Conext or XW System, and transmits it to the included widget-based monitoring software for a simple and graphically rich view of system performance. More than a data logger, the Gateway offers a web page with the ability to configure automated email reports and fault status to the user or installer.
The Gateway includes both built-in Wi-Fi and Ethernet connectivity allowing for flexible and simple set up for wireless or wired connection to a router or direct to a PC.
Features
    Can monitor a network consisting of up to 20 single-phase Conext inverters or up to 8 Conext XW devices (XW Inverter/Charger(s),SW, XW MPPT Solar Charge Controllers(s), XW SCP, and XW AGS)
  • Wi-Fi/Ethernet module with 10/100 Base-T ot 802.11 b/g
  • Can be configured to send energy and alarm reports via email
  • Graphical interactive solar monitoring software
  • Embedded web page for configuring the Xantrex Gateway and upgrading inverter firmware
  • 16 megabytes of storage
  • Simple Modbus over RS485 for limited external system and device monitoring
The Gateway logs and transmits performance data including:
    System power performance
  • Inverter specific power production
  • Lifetime energy production; daily, weekly, monthly energy production graphs
  • Inverter faults with date and time stamp
Conext 2.8kW Schneider Electric Grid Tied Inverter 208V/240V
Offering high performance, clean aesthetics, innovative features, and easy installation, the Conext™ TX provides great value in a compact high-frequency design. The Conext TX may be installed as a single inverter for a single PV array or in a multiple inverter configuration for large PV systems or three-phase

Features:
Superior Design

  • Compact package and light weight
  • Included 600V Square D DC/AC safety disconnect for a clean, compact installation
  • Passively cooled for low noise, increased reliability, and increased installation options
  • LCD vibration sensor allows the tap of a finger to turn backlight on and cycle through display screens

Excellent Energy Harvest

  • Wide maximum power point tracking (MPPT) window from PV solar array maximizes energy harvest and increases array design flexibility
  • Innovative Fast Sweep MPPT increases energy harvest in shaded installations
  • High efficiency CEC weighted up to 96%

Easy to Install and Service

  • Convection cooled increased mounting options, mounts on standard 16” stud configuration
  • Easy access DC (PV) and AC (Utility) terminal blocks simplify wiring
  • Power levels optimized for common service panel breaker sizes
  • Simple communications set-up for daisy-chained single-phase and three-phase installations
  • Sealed inverter enclosure can be quickly separated from wiring box allowing DC/AC connections to remain intact during service event

Designed for Reliability

    Multiple Environmental Over Stressed Testing (MEOST)
Applications
  • Residential and commercial installations (208 or 240 V)
  • Compatible with other Series models to customize the inverters to the array

Conext 3.3kW Schneider Electric Grid Tied Inverter 208V/240V
Offering high performance, clean aesthetics, innovative features, and easy installation, the Conext™ TX provides great value in a compact high-frequency design. The Conext TX may be installed as a single inverter for a single PV array or in a multiple inverter configuration for large PV systems or three-phase

Features:
Superior Design

  • Compact package and light weight
  • Included 600V Square D DC/AC safety disconnect for a clean, compact installation
  • Passively cooled for low noise, increased reliability, and increased installation options
  • LCD vibration sensor allows the tap of a finger to turn backlight on and cycle through display screens

Excellent Energy Harvest

  • Wide maximum power point tracking (MPPT) window from PV solar array maximizes energy harvest and increases array design flexibility
  • Innovative Fast Sweep MPPT increases energy harvest in shaded installations
  • High efficiency CEC weighted up to 96%

Easy to Install and Service

  • Convection cooled increased mounting options, mounts on standard 16” stud configuration
  • Easy access DC (PV) and AC (Utility) terminal blocks simplify wiring
  • Power levels optimized for common service panel breaker sizes
  • Simple communications set-up for daisy-chained single-phase and three-phase installations
  • Sealed inverter enclosure can be quickly separated from wiring box allowing DC/AC connections to remain intact during service event

Designed for Reliability

    Multiple Environmental Over Stressed Testing (MEOST)
Applications
  • Residential and commercial installations (208 or 240 V)
  • Compatible with other Series models to customize the inverters to the array

Conext 3.8kW Schneider Electric Grid Tied Inverter 208V/240V
Offering high performance, clean aesthetics, innovative features, and easy installation, the Conext™ TX provides great value in a compact high-frequency design. The Conext TX may be installed as a single inverter for a single PV array or in a multiple inverter configuration for large PV systems or three-phase

Features:
Superior Design

  • Compact package and light weight
  • Included 600V Square D DC/AC safety disconnect for a clean, compact installation
  • Passively cooled for low noise, increased reliability, and increased installation options
  • LCD vibration sensor allows the tap of a finger to turn backlight on and cycle through display screens

Excellent Energy Harvest

  • Wide maximum power point tracking (MPPT) window from PV solar array maximizes energy harvest and increases array design flexibility
  • Innovative Fast Sweep MPPT increases energy harvest in shaded installations
  • High efficiency CEC weighted up to 96%

Easy to Install and Service

  • Convection cooled increased mounting options, mounts on standard 16” stud configuration
  • Easy access DC (PV) and AC (Utility) terminal blocks simplify wiring
  • Power levels optimized for common service panel breaker sizes
  • Simple communications set-up for daisy-chained single-phase and three-phase installations
  • Sealed inverter enclosure can be quickly separated from wiring box allowing DC/AC connections to remain intact during service event

Designed for Reliability

    Multiple Environmental Over Stressed Testing (MEOST)
Applications
  • Residential and commercial installations (208 or 240 V)
  • Compatible with other Series models to customize the inverters to the array




Technical Specifications:

Product Weight:
0.283 lbs
Product Depth: 4.000 inches
Product Height: 3.200 inches
Product Width:
7.000 inches
MC4 CABLE
Our Price: $10.00
MC4 LEAD CABLE
Our Price: $10.00
Enphase, Frame Mount, for 40mm module frame, Qty. 1, EFM-40MM

Technical Specifications:
Product Weight: 0.283 lbs
Product Depth: 4.000 inches
Product Height: 3.200 inches
Product Width: 7.000 inches

MC4 Cable - 3FT MC4 Lead Cables 1.5FT Sets
MC4 CABLE
Our Price: $14.00
Use the disconnect tool for unplugging drop cables and removing the M215 and M250 from connectors. Plan to use at least one per installation.

Technical Specifications:
Product Weight: 0.080 lbs
Product Depth: 2.000 inches
Product Height:
1.000 inches

Product Width: 3.250 inches
600 Volt Combiner Box Fuse Holder - DIN Rail Mount.

These fuse holders fit in:
  • Outback FLEXware Combiner Box
  • Outback FLEXware Combiner Box
  • Midnite Combiner Box
  • Midnite E-Panel
  • Midnite Mini DC
  • Midnite Solar BabyBox 4 Slot AC or DC Breaker Panel combiner boxes and power panels.
MC4 Cable - 5FT
MC4 LEAD CABLE
Our Price: $14.00
MC4 CABLE
Our Price: $16.00
MC4 LEAD CABLE
Our Price: $16.00
MC4 Lead Cables 2.5FT Sets MC4 Cable - 10FT MC4 Lead Cables 5FT Sets
MC4 CABLE
Our Price: $20.00
MC4 LEAD CABLE
Our Price: $20.00
MC4 CABLE
Our Price: $24.00
MC4 Cable - 15FT MC4 Lead Cables 7.5FT Sets MC4 Cable - 20FT
MC4 LEAD CABLE
Our Price: $24.00
MC4 CABLE
Our Price: $28.00
MC4 Lead Cables 10FT Sets One terminator needed per branch circuit. For use with the Enphase M215 and M250.

Technical Specifications:

Product Weight 0.020 lbs
Product Depth 1.500 inches
Product Height 1.000 inches
Product Width 1.500 inches

MC4 Cable - 25FT
MC4 LEAD CABLE
Our Price: $28.00
MC4 CABLE
Our Price: $35.00
MC4 LEAD CABLE
Our Price: $35.00
MC4 Lead Cables 12.5FT Sets MC4 Cable - 30FT MC4 Lead Cables 15FT Sets
MC4 CABLE
Our Price: $40.00
Product Overview

Engage AC Trunk Cable, 3-Ph (5-Wire) for M215 and M250, Per Connector Qty, Continuous length in Landscape (67").

The Engage™ Cable is a continuous length of 12AWG cable with pre-installed connectors for Enphase Microinverters. The cable is handled like standard outdoor-rated electrical wire, allowing it to be cut, spliced and extended as needed.

The Engage Accessories complement the Engage Cable and give it the ability to adapt to any installation.

Features:

Fast

  • Quick installation
  • Large branch capacity
Flexible
  • Simple design
  • No additional cables
Safe
  • No high voltage DC
  • Reduced fire risk
Technical Specifications
Product Weight: 0.900 lbs
Product Depth: 40.000 inches
Product Height: 0.500 inches
Product Width: 0.500 inches


Engage AC Trunk Cable, 1-Ph (4-Wire) for M215 and M250, Per Connector Qty, Continuous length in Portrait (40").

The Engage Cable is a continuous length of 12AWG cable with pre-installed connectors for Enphase Microinverters. The cable is handled like standard outdoor-rated electrical wire, allowing it to be cut, spliced and extended as needed.

The Engage Accessories complement the Engage Cable and give it the ability to adapt to any installation.
FEATURES
Fast

Quick installation
Large branch capacity

Flexible

Simple design
No additional cables

Safe

No high voltage DC
Reduced fire risk

Technical Specifications:
Product Weight 0.800 lbs
Product Depth 40.000 inches
Product Height 0.500 inches
Product Width 0.500 inches
MC4 Cable - 35FT